View MIC4452_4341525.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC4451/4452
Micrel, Inc.
MIC4451/4452
12A-Peak Low-Side MOSFET Driver Bipolar/CMOS/DMOS Process
General Description
MIC4451 and MIC4452 CMOS MOSFET drivers are tough, efficient, and easy to use. The MIC4451 is an inverting driver, while the MIC4452 is a non-inverting driver. Both versions are capable of 12A (peak) output and can drive the largest MOSFETs with an improved safe operating margin. The MIC4451/4452 accepts any logic input from 2.4V to VS without external speed-up capacitors or resistor networks. Proprietary circuits allow the input to swing negative by as much as 5V without damaging the part. Additional circuits protect against damage from electrostatic discharge. MIC4451/4452 drivers can replace three or more discrete components, reducing PCB area requirements, simplifying product design, and reducing assembly cost. Modern Bipolar/CMOS/DMOS construction guarantees freedom from latch-up. The rail-to-rail swing capability of CMOS/DMOS insures adequate gate voltage to the MOSFET during power up/down sequencing. Since these devices are fabricated on a self-aligned process, they have very low crossover current, run cool, use little power, and are easy to drive.
Features
* BiCMOS/DMOS Construction * Latch-Up Proof: Fully Isolated Process is Inherently Immune to Any Latch-up. * Input Will Withstand Negative Swing of Up to 5V * Matched Rise and Fall Times ............................... 25ns * High Peak Output Current .............................12A Peak * Wide Operating Range .............................. 4.5V to 18V * High Capacitive Load Drive ........................... 62,000pF * Low Delay Time .............................................30ns Typ. * Logic High Input for Any Voltage from 2.4V to VS * Low Supply Current .............. 450A With Logic 1 Input * Low Output Impedance .........................................1.0 * Output Voltage Swing to Within 25mV of GND or VS * Low Equivalent Input Capacitance (typ) ................. 7pF
Applications
* * * * * * * * Switch Mode Power Supplies Motor Controls Pulse Transformer Driver Class-D Switching Amplifiers Line Drivers Driving MOSFET or IGBT Parallel Chip Modules Local Power ON/OFF Switch Pulse Generators
Functional Diagram
VS
0.1mA
0.3mA
MIC4451 INVERTING
OUT
IN
2k
MIC4452 NONINVERTING
GND
Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
July 2005
1
MIC4451/4452
MIC4451/4452
Micrel, Inc.
Ordering Information
Part Number Standard MIC4451BN MIC4451BM MIC4451CT MIC4452BN MIC4452BM MIC4452CT Pb-Free MIC4451YN MIC4451YM MIC4451ZT MIC4452YN MIC4452YM MIC4452ZT Temperature Range -40C to +85C -40C to +85C 0C to +70C -40C to +85C -40C to +85C 0C to +70C Package 8-pin Plastic DIP 8-pin SOIC 5-pin TO-220 8-pin Plastic DIP 8-pin SOIC 5-pin TO-220 Configuration Inverting Inverting Inverting Non-Inverting Non-Inverting Non-Inverting
Pin Configurations
VS 1
IN 2
NC 3
GND 4
Plastic DIP (N) SOIC (M)
8 VS 7 OUT 6 OUT 5 GND
5 4 3 2 1
TO-220-5 (T)
OUT GND VS GND IN
Pin Description
Pin Number TO-220-5 1 2, 4 3, TAB 5 Pin Number DIP, SOIC 2 4, 5 1, 8 6, 7 3 Pin Name IN GND VS OUT NC Pin Function Control Input Ground: Duplicate pins must be externally connected together. Supply Input: Duplicate pins must be externally connected together. Output: Duplicate pins must be externally connected together. Not connected.
MIC4451/4452
2
July 2005
MIC4451/4452
Micrel, Inc. (Notes 1, 2 and 3)
Absolute Maximum Ratings
Operating Ratings
Operating Temperature (Chip) ................................... 150C Operating Temperature (Ambient) C Version .................................................... 0C to +70C B Version ................................................ -40C to +85C Thermal Impedances (To Case) 5-Pin TO-220 (JC) ............................................... 10C/W
Supply Voltage .............................................................. 20V Input Voltage ...................................VS + 0.3V to GND - 5V Input Current (VIN > VS) .............................................. 50 mA Power Dissipation, TAMBIENT 25C PDIP .................................................................... 960mW SOIC .................................................................. 1040mW 5-Pin TO-220 .............................................................. 2W Power Dissipation, TCASE 25C 5-Pin TO-220 ......................................................... 12.5W Derating Factors (to Ambient) PDIP ................................................................ 7.7mW/C SOIC ............................................................... 8.3 mW/C 5-Pin TO-220 .................................................... 17mW/C Storage Temperature ................................ -65C to +150C Lead Temperature (10 sec) ....................................... 300C
Electrical Characteristics(Note 4):
(TA = 25C with 4.5 V VS 18 V unless otherwise specified.) Symbol INPUT VIH VIL VIN IIN OUTPUT VOH VOL RO RO IPK IDC IR High Output Voltage Low Output Voltage Output Resistance, Output High Output Resistance, Output Low Peak Output Current Continuous Output Current Latch-Up Protection Withstand Reverse Current Rise Time Fall Time Delay Time Delay Time Power Supply Current Operating Input Voltage Duty Cycle 2% t 300 s Test Figure 1, CL = 15,000 pF Test Figure 1, CL = 15,000 pF Test Figure 1 Test Figure 1 VIN = 3 V VIN = 0 V 4.5 See Figure 1 See Figure 1 IOUT = 10 mA, VS = 18V IOUT = 10 mA, VS = 18V VS = 18 V (See Figure 6) 2 >1500 0.6 0.8 12 VS-.025 .025 1.5 1.5 V V A A mA Logic 1 Input Voltage Logic 0 Input Voltage Input Voltage Range Input Current 0 V VIN VS -5 -10 2.4 1.3 1.1 0.8 VS+.3 10 V V V A Parameter Conditions Min Typ Max Units
SWITCHING TIME (Note 3) tR tF tD1 tD2 IS VS 20 24 15 35 0.4 80 40 50 30 60 1.5 150 18 ns ns ns ns mA A V
Power Supply
July 2005
3
MIC4451/4452
MIC4451/4452
Micrel, Inc.
Electrical Characteristics:
(Over operating temperature range with 4.5V < VS < 18V unless otherwise specified.) Symbol INPUT VIH VIL VIN IIN OUTPUT VOH VOL RO RO High Output Voltage Low Output Voltage Output Resistance, Output High Output Resistance, Output Low Rise Time Fall Time Delay Time Delay Time Power Supply Current Operating Input Voltage Figure 1 Figure 1 IOUT = 10mA, VS = 18V IOUT = 10mA, VS = 18V 0.8 1.3 VS-.025 0.025 2.2 2.2 V V Logic 1 Input Voltage Logic 0 Input Voltage Input Voltage Range Input Current 0V VIN VS -5 -10 2.4 1.4 1.0 0.8 VS+.3 10 V V V A Parameter Conditions Min Typ Max Units
SWITCHING TIME (Note 3) tR tF tD1 tD2 IS VS NOTE 1: NOTE 2: NOTE 3: NOTE 4: Figure 1, CL = 15,000pF Figure 1, CL = 15,000pF Figure 1 Figure 1 VIN = 3V VIN = 0V 4.5 23 30 20 40 0.6 0.1 50 60 40 80 3 0.4 18 ns ns ns ns mA V
POWER SUPPLY
Functional operation above the absolute maximum stress ratings is not implied. Static-sensitive device. Store only in conductive containers. Handling personnel and equipment should be grounded to prevent damage from static discharge. Switching times guaranteed by design. Specification for packaged product only.
Test Circuits
VS = 18V 0.1F
OUT 15000pF
VS = 18V 1.0F
0.1F
IN MIC4451
0.1F
IN MIC4452
0.1F
OUT 15000pF
1.0F
INPUT
5V 90% 10% 0V
VS 90%
tP W
2.5V tP W 0.5s
INPUT
5V 90% 10% 0V
VS 90%
tD1
tP W
2.5V tP W 0.5s
tD1
tF
tD2
tR
tR
tD2
tF
O U TPU T
O U TPU T
10% 0V
10% 0V
Figure 1. Inverting Driver Switching Time MIC4451/4452 4
Figure 2. Noninverting Driver Switching Time July 2005
MIC4451/4452
Micrel, Inc.
Typical Characteristic Curves
Rise Time vs. Supply Voltage Fall Time vs. Supply Voltage Rise and FallTimes vs. Temperature
CL = 10,000pF V S = 18V tFALL
220 200 180 160 140 120 100 80 60 40 20 0
R IS E T IM E (n s )
220 200 180 160 140 120 100 80 60 40 20 0
F A L L T IM E (n s )
60 50
T IM E (n s )
40 30 20 10
47,000pF
47,000pF
22,000pF 10,000pF 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) 18
22,000pF 10,000pF 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) 18
tRISE
0
-40
0
40
80
120
TEMPERATURE ( C)
300 250
R IS E T IM E (n s )
Rise Time vs. Capacitive Load
5V
300 250
F A L L T IM E (n s )
Fall Time vs. Capacitive Load
C R O S S O V E R E N E R G Y (A *s )
10 -7
Crossover Energy vs. Supply Voltage
PER TRANSITION
200 150 10V 100 50 0 100 1000 10k CAPACITIVE LOAD (pF) 18V 100k
200 150 100 50 0 100 10V
5V
10 -8
18V
1000 10k CAPACITIVE LOAD (pF)
100k
10 -9
4
6
8 10 12 14 VOLTAGE (V)
16
18
S U P P L Y C U R R E N T (m A )
S U P P L Y C U R R E N T (m A )
120 90 60 30 0
20
S U P P L Y C U R R E N T (m A )
220 200 180 160 140 120 100 80 60 40 20 0
Supply Current vs. Capacitive Load
V S = 18V
150
Supply Current vs. Capacitive Load
V S = 12V
75 60 45 30 15 0
Supply Current vs. Capacitive Load
V S = 5V
H 1M
z
z
z
20
100
1000 10k CAPACITIVE LOAD (pF)
100k
100
1000 10k CAPACITIVE LOAD (pF)
100k
100
1000 10k CAPACITIVE LOAD (pF)
20
1
50
50
0k
0k
0k
50
z MH
1M
Hz
kH
kH
H
H
H
180
S U P P L Y C U R R E N T (m A )
Supply Current vs. Frequency
V S = 18V
S U P P L Y C U R R E N T (m A )
120 100 80 60 40 20 0
Supply Current vs. Frequency
V S = 12V
S U P P L Y C U R R E N T (m A )
60 50 40 30 20 10 0
Supply Current vs. Frequency
V S = 5V
0 .0 1 F
160 140 120 100 80 60 40 20 0
F
F
F
0 .1
0 .1
0 .0 1
F
pF
1000
0 .0 1
1000
0 .1
pF
F
10k
100k 1M FREQUENCY (Hz)
10M
10k
100k 1M FREQUENCY (Hz)
10M
10k
100k 1M FREQUENCY (Hz)
1000
pF
kH
z
z
z
July 2005
5
MIC4451/4452
z
100k
10M
MIC4451/4452
Micrel, Inc.
Typical Characteristic Curves (Cont.)
Propagation Delay vs. Supply Voltage Propagation Delay vs. Input Amplitude
V S = 10V 40
T IM E (n s )
50 40
T IM E (n s )
T IM E (n s )
30 20 10 0
t D2
t D1
4
6 8 10 12 14 16 SUPPLY VOLTAGE (V)
18
120 110 100 90 80 70 60 50 40 30 20 10 0
50
Propagation Delay vs. Temperature
30 20 10
t D2
tD2
t D1
0
2
4 6 INPUT (V)
tD1 8
10
0
-40 0 40 80 TEMPERATURE ( C)
120
H IG H -S T A T E O U T P U T R E S IS T A N C E ()
L O W -S T A T E O U T P U T R E S IS T A N C E ()
Q U IE S C E N T S U P P L Y C U R R E N T ( A )
1000
Quiescent Supply Current vs. Temperature
V S = 18V INPUT = 1
100 INPUT = 0
10
-40 0 40 80 TEMPERATURE ( C)
120
2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0
High-State Output Resist. vs. Supply Voltage
Low-State Output Resist. vs. Supply Voltage
2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0
T J = 150 C T J = 25 C
T J = 150 C
T J = 25 C
4
6
8 10 12 14 16 SUPPLY VOLTAGE (V)
18
4
6
8 10 12 14 16 SUPPLY VOLTAGE (V)
18
MIC4451/4452
6
July 2005
MIC4451/4452
Micrel, Inc. To guarantee low supply impedance over a wide frequency range, a parallel capacitor combination is recommended for supply bypassing. Low inductance ceramic disk capacitors with short lead lengths (< 0.5 inch) should be used. A 1F low ESR film capacitor in parallel with two 0.1F low ESR ceramic capacitors, (such as AVX RAM GUARD(R)), provides adequate bypassing. Connect one ceramic capacitor directly between pins 1 and 4. Connect the second ceramic capacitor directly between pins 8 and 5. Grounding The high current capability of the MIC4451/4452 demands careful PC board layout for best performance. Since the MIC4451 is an inverting driver, any ground lead impedance will appear as negative feedback which can degrade switching speed. Feedback is especially noticeable with slow-rise time inputs. The MIC4451 input structure includes 200mV of hysteresis to ensure clean transitions and freedom from oscillation, but attention to layout is still recommended. Figure 5 shows the feedback effect in detail. As the MIC4451 input begins to go positive, the output goes negative and several amperes of current flow in the ground lead. As little as 0.05 of PC trace resistance can produce hundreds of millivolts at the MIC4451 ground pins. If the driving logic is referenced to power ground, the effective logic input level is reduced and oscillation may result. To insure optimum performance, separate ground traces should be provided for the logic and power connections. Connecting the logic ground directly to the MIC4451 GND pins will ensure full logic drive to the input and ensure fast output switching. Both of the MIC4451 GND pins should, however, still be connected to power ground.
Applications Information
Supply Bypassing Charging and discharging large capacitive loads quickly requires large currents. For example, changing a 10,000pF load to 18V in 50ns requires 3.6A. The MIC4451/4452 has double bonding on the supply pins, the ground pins and output pins. This reduces parasitic lead inductance. Low inductance enables large currents to be switched rapidly. It also reduces internal ringing that can cause voltage breakdown when the driver is operated at or near the maximum rated voltage. Internal ringing can also cause output oscillation due to feedback. This feedback is added to the input signal since it is referenced to the same ground.
V DD
1F
MIC4451
V DD
2
1 D R I V E S I G N A L CONDUCTION ANGLE CONTROL 0 TO 180 CONDUCTION ANGLE CONTROL 1 8 0 TO 3 6 0
DRIVE LOGIC
1
V DD
M
3
1F
MIC4452
V DD
PHASE 1 OF 3 PHASE MOTOR D R I VER U SI N G M I C 4 4 5 1 / 4 4 5 2
Figure 3. Direct Motor Drive
+15
(x2) 1N4448
5.6 k
OUTPUT VOLTAGE vs LOAD CURRENT
560
0.1F 50V
+
30
29
BYV 10 (x 2)
+
VOLTS
1
2
1F 50V MKS2
6, 7
28 27 26 25 0 50 100 150 200 250 300 350
12 LINE
8
0.1F WIMA MKS2
MIC4451
4 5
+ 560F 50V 100F 50V UNIT E D CHE MCON S X E
mA
Figure 4. Self Contained Voltage Doubler
July 2005
7
MIC4451/4452
MIC4451/4452 Input Stage The input voltage level of the MIC4451 changes the quiescent supply current. The N channel MOSFET input stage transistor drives a 320A current source load. With a logic "1" input, the maximum quiescent supply current is 400A. Logic "0" input level signals reduce quiescent current to 80A typical. The MIC4451/4452 input is designed to provide 200mV of hysteresis. This provides clean transitions, reduces noise sensitivity, and minimizes output stage current spiking when changing states. Input voltage threshold level is approximately 1.5V, making the device TTL compatible over the full temperature and operating supply voltage ranges. Input current is less than 10A. The MIC4451 can be directly driven by the TL494, SG1526/1527, SG1524, TSC170, MIC38C42, and similar switch mode power supply integrated circuits. By offloading the power-driving duties to the MIC4451/4452, the power supply controller can operate at lower dissipation. This can improve performance and reliability. The input can be greater than the VS supply, however, current will flow into the input lead. The input currents can be as high as 30mA p-p (6.4mARMS) with the input. No damage will occur to MIC4451/4452 however, and it will not latch. The input appears as a 7pF capacitance and does not change even if the input is driven from an AC source. While the device will operate and no damage will occur up to 25V below the negative rail, input current will increase up to 1mA/V due to the clamping action of the input, ESD diode, and 1k resistor. Power Dissipation CMOS circuits usually permit the user to ignore power dissipation. Logic families such as 4000 and 74C have outputs which can only supply a few milliamperes of current, and even shorting outputs to ground will not force enough current to destroy the device. The MIC4451/4452 on the other hand, can source or sink several amperes and drive large capacitive loads at high frequency. The package power dissipation limit can easily be exceeded. Therefore, some attention should be given to power dissipation when driving low impedance loads and/or operating at high frequency.
+18
Micrel, Inc. The supply current vs. frequency and supply current vs capacitive load characteristic curves aid in determining power dissipation calculations. Table 1 lists the maximum safe operating frequency for several power supply voltages when driving a 10,000pF load. More accurate power dissipation figures can be obtained by summing the three dissipation sources. Given the power dissipation in the device, and the thermal resistance of the package, junction operating temperature for any ambient is easy to calculate. For example, the thermal resistance of the 8-pin plastic DIP package, from the data sheet, is 130C/W. In a 25C ambient, then, using a maximum junction temperature of 125C, this package will dissipate 960mW. Accurate power dissipation numbers can be obtained by summing the three sources of power dissipation in the device: * Load Power Dissipation (PL) * Quiescent power dissipation (PQ) * Transition power dissipation (PT) Calculation of load power dissipation differs depending on whether the load is capacitive, resistive or inductive. Resistive Load Power Dissipation Dissipation caused by a resistive load can be calculated as: PL = I2 RO D where: I= RO = D= the current drawn by the load the output resistance of the driver when the output is high, at the power supply voltage used. (See data sheet) fraction of time the load is conducting (duty cycle)
Capacitive Load Power Dissipation Dissipation caused by a capacitive load is simply the energy placed in, or removed from, the load capacitance by the driver. The energy stored in a capacitor is described by the equation: E = 1/2 C V2
WIMA MKS-2 1 F
5.0V
1 8
MIC4451
6, 7
TEK CURRENT PROBE 6302
18 V
0V
0.1F
4
5
0.1F
0V
2,500 pF POLYCARBONATE
LOGIC GROUND POWER GROUND
300 mV
12 AMPS
PC TRACE RESISTANCE = 0.05
Table 1: MIC4451 Maximum Operating Frequency VS Max Frequency 18V 220kHz 15V 300kHz 10V 640kHz 5V 2MHz
Conditions: 1. JA = 150C/W 2. TA = 25C 3. CL = 10,000pF
Figure 5. Switching Time Degradation Due to Negative Feedback MIC4451/4452 8 July 2005
MIC4451/4452 As this energy is lost in the driver each time the load is charged or discharged, for power dissipation calculations the 1/2 is removed. This equation also shows that it is good practice not to place more voltage on the capacitor than is necessary, as dissipation increases as the square of the voltage applied to the capacitor. For a driver with a capacitive load: PL = f C (VS)2 where: f = Operating Frequency C = Load Capacitance VS =Driver Supply Voltage Inductive Load Power Dissipation For inductive loads the situation is more complicated. For the part of the cycle in which the driver is actively forcing current into the inductor, the situation is the same as it is in the resistive case: PL1 = I RO D
2
Micrel, Inc. Transition Power Dissipation Transition power is dissipated in the driver each time its output changes state, because during the transition, for a very brief interval, both the N- and P-channel MOSFETs in the output totem-pole are ON simultaneously, and a current is conducted through them from VS to ground. The transition power dissipation is approximately: PT = 2 f VS (A*s) where (A*s) is a time-current factor derived from the typical characteristic curve "Crossover Energy vs. Supply Voltage." Total power (PD) then, as previously described is: PD = PL + PQ + PT Definitions CL = Load Capacitance in Farads. D = Duty Cycle expressed as the fraction of time the input to the driver is high. f = Operating Frequency of the driver in Hertz IH = Power supply current drawn by a driver when both inputs are high and neither output is loaded. IL = Power supply current drawn by a driver when both inputs are low and neither output is loaded. ID = Output current from a driver in Amps. PD = Total power dissipated in a driver in Watts. PL = Power dissipated in the driver due to the driver's load in Watts. PQ = Power dissipated in a quiescent driver in Watts. PT = Power dissipated in a driver when the output changes states ("shoot-through current") in Watts. NOTE: The "shoot-through" current from a dual transition (once up, once down) for both drivers is stated in Figure 7 in ampere-nanoseconds. This figure must be multiplied by the number of repetitions per second (frequency) to find Watts. RO = Output resistance of a driver in Ohms. VS = Power supply voltage to the IC in Volts.
However, in this instance the RO required may be either the on resistance of the driver when its output is in the high state, or its on resistance when the driver is in the low state, depending on how the inductor is connected, and this is still only half the story. For the part of the cycle when the inductor is forcing current through the driver, dissipation is best described as PL2 = I VD (1 - D) where VD is the forward drop of the clamp diode in the driver (generally around 0.7V). The two parts of the load dissipation must be summed in to produce PL PL = PL1 + PL2 Quiescent Power Dissipation Quiescent power dissipation (PQ, as described in the input section) depends on whether the input is high or low. A low input will result in a maximum current drain (per driver) of 0.2mA; a logic high will result in a current drain of 3.0mA. Quiescent power can therefore be found from: PQ = VS [D IH + (1 - D) IL] where: IH = IL = D= VS = quiescent current with input high quiescent current with input low fraction of time input is high (duty cycle) power supply voltage
July 2005
9
MIC4451/4452
MIC4451/4452
Micrel, Inc.
+18 V
WIMA MK22 1 F
5.0V
2
1 8
MIC4452
4 5
6, 7
TEK CURRENT PROBE 6302
18 V
0V
0.1F
0.1F
0V
15,000 pF POLYCARBONATE
Figure 6. Peak Output Current Test Circuit
MIC4451/4452
10
July 2005
MIC4451/4452
Micrel, Inc.
Package Information
PIN 1 DIMENSIONS: INCH (MM)
0.380 (9.65) 0.370 (9.40)
0.135 (3.43) 0.125 (3.18)
0.255 (6.48) 0.245 (6.22) 0.300 (7.62) 0.013 (0.330) 0.010 (0.254)
0.018 (0.57) 0.100 (2.54)
0.130 (3.30) 0.0375 (0.952)
0.380 (9.65) 0.320 (8.13)
8-Pin Plastic DIP (N)
0.026 (0.65) MAX)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.050 (1.27) TYP
0.020 (0.51) 0.013 (0.33) 0.0098 (0.249) 0.0040 (0.102) 0-8 SEATING PLANE 45 0.010 (0.25) 0.007 (0.18)
0.064 (1.63) 0.045 (1.14)
0.197 (5.0) 0.189 (4.8)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79)
8-Pin SOIC (M)
July 2005
11
MIC4451/4452
MIC4451/4452
Micrel, Inc.
0.150 D 0.005 (3.81 D 0.13) 0.400 0.015 (10.16 0.38) 0.108 0.005 (2.74 0.13)
0.241 0.017 (6.12 0.43)
0.177 0.008 (4.50 0.20) 0.050 0.005 (1.27 0.13)
0.578 0.018 (14.68 0.46)
SEATING PLANE
7 Typ. 0.550 0.010 (13.97 0.25)
0.067 0.005 (1.70 0.127)
0.268 REF (6.81 REF)
0.032 0.005 (0.81 0.13)
0.018 0.008 (0.46 0.20)
0.103 0.013 (2.62 0.33)
Dimensions: inch (mm)
5-Pin TO-220 (T)
MICREL INC.
TEL
+ 1 (408) 944-0800
2180 FORTUNE DRIVE
FAX
+ 1 (408) 474-1000
SAN JOSE, CA 95131
WEB
http://www.micrel.com
USA
This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 1998 Micrel, Inc.
MIC4451/4452
12
July 2005

▲Up To Search▲

Price & Availability of MIC4452

	To Download MIC4452 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .